If you have any difficulty navigating the java buttons below, click here for a full web directory.

 

Wise Gas
CNG Dispensers

Wise Gas, Inc. Corporate Information

Products, Services & Capabilities

Wise Gas Education & Information

Industry News

Editorials & Discussions

Our Partners & Supporters

 


CNG Dispensers

Below is a sampling of dispensers that Wise Gas, Inc. has available. 

Contact Wise Gas for Pricing or Questions
 

TGT-T7103-6CNG50
Single High Hose Stand Alone CNG Vehicle Dispenser

This dispenser is a three-line dispenser that independently meters the gas and gives you a display on both sides of the dispenser. Flow Rate as high as 3000cfm have been seen with this dispenser in certain configurations. Standard flow rate is 1500cfm. The New Micro Motion ® CNG50 sensor is used in this dispenser to achieve the flow rate. The dispenser has 2, 4-20mA output that can send flow or temperature to a remote controller. The dispenser has a dry contact and a 120VAC hook switch for an "in use" signal and will send pulses to a card reader or a console. The Micro Motion ® transmitters are located within the dispenser body and are factory set up and calibrated before shipment. TGT assembles an AGA 1-93 approved Parker Parflex CNG fill hose on all its dispensers. The Breakaway is the Snap-tite In-Line type with a unique vent Breakaway attached to the fill hose Breakaway. This CNG Dispenser has an ASME pressure relief valve inside the dispenser cabinet with a vent stack up through the dispenser body. The cabinet is constructed of 11-gauge cold roll steel with a powder-coated finish; stainless steel material is optional. The high body style gives you the look of contemporary gasoline dispenser. The standard color is black with white faces and doors but any custom colors can be applied to the dispenser body. This dispenser will temperature compensate the fill pressure of the gas and do electronic sequencing of the gas from the storage to the dispenser using the Acufill® algorithm. This dispenser will communicate with a card reader via pulse (gasoline standard mechanical type pulsars). Model number will change any with options selected.

Each Includes:
3    Solenoid Sequencing Valves
1    Pressure Gauge
1    Snap-tite In-Line Break-away
1    Manual Shutoff Valve
1    1 Powder Coated Cold Roll Carbon Steel Body (Stainless Steel Optional)
1    Micro Motion CNG50 Mass Flow Meters (rated at 5000 Psi(345 bar), 170 lbs./min (77kg/min.), 3000 scfm) Flow Rates through the dispenser depends on vehicle capacity to receive gas and nozzle attached to dispenser hose. A ˝" hose and a nozzle upgrade is required for flow rates above 1500scfm(42.47m3/Min).
1    ASME Relief Valve
2    2 10 (3.5m)' x 3/8"4500(mil) Hose Assembly (electrically conductive CNG twin hose)
1    Back lighted TGT Electronic Single Hose Head
Tubing is 3/8" .049 316 Seamless Stainless Steel
Optional:
Two Drop Sequencing Solenoid Valve Panel Remote from Dispenser
Two Drop Sequencing ˝" Ball Valve Panel Remote from Dispenser
NGV1 Type 2 Refueling Connector Nozzle (Staubli)
NGV1 Type 1 Refueling Nozzle Sherex CT1000
1 Parker Finite J2SD Filter Installed in Dispenser
1 Parker Finite J4SD Filter Installed in Dispenser
Dispenser Base Shear Break-away System Installed in Dispenser
Stainless Steel Body with powder coat paint
Pressure Regulator used when dual pressure and elevated storage
Upgrade to ˝" Hose
High Flow Rate Nozzles call for quote

This dispenser is manufactured under the guidelines of:
NFPA 52
NFPA 70 (NEC)
ANSI/IAS NGV 4.0-1999 CSA 12.00-M99
ANSI B31.3
CENELEC (on request)

Contact Wise Gas for Pricing

 

 

TGT-T7203-6CNG50
Twin High Hose Stand Alone CNG Vehicle Dispenser

This dispenser is a three-line dispenser that independently meters the gas and gives you a display on both sides of the dispenser. Flow Rate as high as 3000cfm have been seen with this dispenser in certain configurations. The New Micro Motion ® CNG50 sensor is used in this dispenser to achieve the flow rate. The dispenser has 2, 4-20mA output that can send flow or temperature to a remote controller. The dispenser has a dry contact and a 120VAC hook switch for an "in use" signal and will send pulses to a card reader or a console. The Micro Motion ® transmitters are located within the dispenser body and are factory set up and calibrated before shipment. TGT assembles an AGA 1-93 approved Parker Parflex CNG fill hose on all its dispensers. The Breakaway is the Snap-tite In-Line type with a unique vent Breakaway attached to the fill hose Breakaway. All TGT CNG Dispensers have an ASME pressure relief valve inside the dispenser cabinet with a vent stack up through the dispenser body. The cabinet is constructed of 11-gauge cold roll steel with a powder-coated finish; stainless steel material is optional. The high body style gives you the look of contemporary gasoline dispenser. The standard color is black but any custom colors can be applied to the dispenser body. This dispenser will temperature compensate the fill pressure of the gas and do electronic sequencing of the gas from the storage to the dispenser using the Acufill® algorithm. All of the sequencing valves are mounted internal in the dispenser. This Dispenser will communicate with a card reader via pulse or Gilbarco protocall. Model Number will change with options selected.

 

Each Includes:
6    Sequencing Valves
2    Pressure Gauges
2    Snap-tite In-Line Break-aways
2    Manual Shutoff Valves
1    Powder Coated Cold Roll Carbon Steel Body (Stainless Steel Optional)
2    Micro Motion CNG50 Mass Flow Meters (rated at 5000 Psi(345 bar), 170 lbs./min (77kg/min.), 3000 scfm) Flow Rates through the dispenser depends on vehicle capacity to receive gas and nozzle attached to dispenser hose. A ˝" hose and a nozzle upgrade is required for flow rates above 1500scfm(42.47m3/Min).
2    ASME Relief Valves
1    Concrete Island Box Form
2    10' (3.5m)' x 3/8"4500(mil) Hose Assemblies (electrically conductive CNG twin hose)
1    Back lighted TGT Electronic Dual Hose Head
Tubing is 3/8" .049 316 Seamless Stainless Steel
Optional:
Two Drop Sequencing Solenoid Valve Panel Remote from Dispenser
Two Drop Sequencing ˝" Ball Valve Panel Remote from Dispenser
NGV1 Type 2 Refueling Connector Nozzle (Staubli)
NGV1 Type 1 Refueling Nozzle Sherex CT1000
2 Parker Finite J2SD Filters Installed in Dispenser w/ Block and Bleed Valves
Dispenser Base Shear Break-away System Installed in Dispenser
Stainless Steel Body with powder coat paint
Pressure Regulator used when dual pressure and elevated storage
Upgrade to ˝" Hose
High Flow Rate Nozzles call for quote

This dispenser is manufactured under the guidelines of:
NFPA 52
NFPA 70 (NEC)
ANSI/IAS NGV 4.0-1999 CSA 12.00-M99
ANSI B31.3
CE (on request)

Contact Wise Gas for Pricing
 
 

TGT-T7100-6CNG50
Single High Hose Stand Alone CNG Vehicle Dispenser

This dispenser is a one-line dispenser that meters the gas and gives you a display on both sides of the dispenser. Flow rates as high as 3000cfm have been seen with this dispenser in certain configurations. Standard flow rate is 1500cfm. The New Micro Motion ® CNG50 sensor is used in this dispenser to achieve the flow rate. The dispenser has 2, 4-20mA output that can send flow or temperature to a remote controller. The dispenser has a dry contact and a 120VAC hook switch for an "in use" signal and will send pulses to a card reader or a console. The Micro Motion ® Transmitters are located within the dispenser body and are factory set up and calibrated before shipment. TGT assembles an AGA 1-93 approved Parker Parflex CNG fill hose on all its dispensers. The Breakaway is the Snap-tite In-Line type with a unique vent Breakaway attached to the fill hose Breakaway. All TGT CNG Dispensers have an ASME pressure relief valve inside the dispenser cabinet with a vent stack up through the dispenser body. The cabinet is constructed of 11-gauge cold roll steel with a powder-coated finish; stainless steel material is optional. The high body style gives you the look of contemporary gasoline dispenser. The standard color is black but any custom colors can be applied to the dispenser body. As an option this dispenser will temperature compensate the fill pressure of the gas and do electronic sequencing of the gas from the storage to the dispenser. This Dispenser will communicate with a card reader via pulse.

 

Each Includes:
1    Solenoid Valve
1    Pressure Gauge 6000psi
1    In-Line Hose Break-away
1    Manual Shutoff Valve
1    Powder Coated Cold Roll Carbon Steel Body (Stainless Steel Optional)
2    Micro Motion CNG50 Mass Flow Meters (rated at 5000 Psi, 170 lbs./min (77kg/min.), 3000 scfm) Flow Rates through the dispenser depends on vehicle capacity to receive gas and nozzle attached to dispenser hose. A ˝" hose and a nozzle upgrade is required for flow rates above 1500scfm
1    ASME Relief Valve
1    Concrete Island Box Form
2    16' x 1/2" Hose Assembly (electrically conductive CNG twin hose)
1    Back lighted TGT Electronic Dual Hose Head

Tubing is 3/8" .065 wall seamless stainless steel
MAWP 5000psi

Optional:
One Drop Sequencing Solenoid Valve Panel Internal in Dispenser
One Drop Sequencing Solenoid Valve Panel Remote from Dispenser
One Drop Sequencing Ball Valve Panel Remote from Dispenser
NGV1 Type 2 Refueling Connector Nozzle (Staubli)
NGV1 Type 1 Refueling Nozzle Sherex CT1000
Parker Finite J2SD Filter Installed in Dispenser
Dispenser Base Shear Break-away System Installed in Dispenser
Stainless Steel Body with powder coat paint
Pressure Regulator (used when dual pressure and elevated storage)

This dispenser is manufactured under the guidelines of:
NFPA 52
NFPA 70 (NEC)
ANSI/IAS NGV 4.0-1999 CSA 12.00-M99
ANSI B31.3

Contact Wise Gas for Pricing

 

TGT-T7200-6CNG50
Twin High Hose Stand Alone CNG Vehicle Dispenser

This dispenser is a two-line dispenser that independently meters the gas and gives you a display on both sides of the dispenser. Flow Rate as high as 3000cfm have been seen with this dispenser in certain configurations. Standard flow rate is 1500cfm. The New Micro Motion ® CNG50 sensor is used in this dispenser to achieve the flow rate. The dispenser has 2, 4-20mA output that can send flow or temperature to a remote controller. The dispenser has a dry contact and a 120VAC hook switch for an "in use" signal and will send pulses to a card reader or a console. The Micro Motion ® transmitters are located within the dispenser body and are factory set up and calibrated before shipment. TGT assembles an AGA 1-93 approved Parker Parflex CNG fill hose on all its dispensers. The Breakaway is the Snap-tite In-Line type with a unique vent Breakaway attached to the fill hose Breakaway. All TGT CNG Dispensers have an ASME pressure relief valve inside the dispenser cabinet with a vent stack up through the dispenser body. The cabinet is constructed of 11-gauge cold roll steel with a powder-coated finish; stainless steel material is optional. The high body style gives you the look of contemporary gasoline dispenser. The standard color is black but any custom colors can be applied to the dispenser body. As an option this dispenser will temperature compensate the fill pressure of the gas and do electronic sequencing of the gas from the storage to the dispenser using the Acufill® algorithm. All of the sequencing valves are mounted internal in the dispenser. This Dispenser will communicate with a card reader via pulse or Gilbarco protocall. Model Number will change with options selected.

Each Includes:
2    Sequencing Valves
1    Pressure Gauge
2    Snap-tite In-Line Break-aways
2    Manual Shutoff Valve
1    Powder Coated Cold Roll Carbon Steel Body (Stainless Steel Optional)
2    Micro Motion CNG50 Mass Flow Meters (rated at 5000 Psi(345 bar), 170 lbs./min (77kg/min.), 3000 scfm) Flow Rates through the dispenser depends on vehicle capacity to receive gas and nozzle attached to dispenser hose. A ˝" hose and a nozzle upgrade is required for flow rates above 1500scfm(42.47m3/Min).
2    ASME Relief Valve
1    Concrete Island Box Form
2    12 (3.5m)' x 3/8"4500(mil) Hose Assembly (electrically conductive CNG twin hose)
1    Back lighted TGT Electronic Dual Hose Head

Tubing is 3/8" .049 316 Seamless Stainless Steel
MAWP 5000psi

Optional:
Two Drop Sequencing Solenoid Valve Panel Internal to the Dispenser
Two Drop Sequencing Solenoid Valve Panel Remote from Dispenser
Two Drop Sequencing ˝" Ball Valve Panel Remote from Dispenser
NGV1 Type 2 Refueling Connector Nozzle (Staubli)
NGV1 Type 1 Refueling Nozzle Sherex CT1000
2 Parker Finite J2SD Filter Installed in Dispenser
Dispenser Base Shear Break-away System Installed in Dispenser
Stainless Steel Body with powder coat paint
Pressure Regulator used when dual pressure and elevated storage
Upgrade to ˝" Hose
High Flow Rate Nozzles call for quote

This dispenser is manufactured under the guidelines of:
NFPA 52
NFPA 70 (NEC)
ANSI/IAS NGV 4.0-1999 CSA 12.00-M99
ANSI B31.3
CENELEC (on request)

Contact Wise Gas for Pricing

 


TGT-K62-1-DH38
Single Hose Stand Alone CNG Vehicle Dispenser

This dispenser is a one-line dispenser that independently meters the gas and gives you a display on both sides of the dispenser. The dispenser has two 4-20ma output that can send flow or temperature to a controller. The dispenser has a dry contact and a 120v hook switch for an "in use" signal and will send pulses to a card reader or a console. The Micro Motion Transmitter is located within the dispenser body and is factory set and calibrated before shipment. TGT assembles an AGA 1-93 approved Parker Paraflex CNG fill hose on all its dispensers. The breakaway is the Snap-tite Inline type with a unique vent breakaway attached to the fill hose breakaway. All 1999 and later CNG Dispensers have an ASME pressure relief valve inside the dispenser cabinet with a vent stack up through the retractor pole. The cabinet is constructed of 11 gauge cold roll steel with a powder coat finish then a high quality mirror stainless steel trim is attached to the outside of the cabinet which will give you years of new appearing equipment. As an option, this dispenser can temperature compensate the fill pressure of the gas and do electronic sequencing of the gas from the storage to the dispenser.

Each Includes:
1    Retractor
1    Solenoid Valve
1    Pressure Gauge
1    Manual Shutoff Valve
1    12' x 3/8" Hose Assembly, AGA Certified 1-93 (electrically conductive CNG twin hose)
1    Micro Motion DH38 Mass Flow Meter (rated at 5000psi, 50 lbs./minute, 1000 cfm)
1    Price Change Communicator
1    Concrete Island Form
1    ASME Relief Valve
  Powder Coated Steel Chassis w/ Stainless Steel Trim
Optional:
Parker Finite J2SD Filter Installed in Dispenser
Dispenser Base Shear Breakaway System Installed in Dispenser
Temperature Compensation from the Dispenser
NGV1 Type 2 Refueling Connector (Staubli)
NGV1 Type 1 Refueling Nozzle (Sherex CT1000)
Three Bank Valve Panel One Hose, Model TGT-VP3B1D
Pressure Regulator used when dual pressure and elevated storage
Upgrade to ˝" Hose
High Flow Rate Nozzles call for quote
Custom screen printed face plates

TGT Valve Panel is designed to flow 1000 cfm with 3/8, .049 seamless stainless steel tubing. The valves are TGT designed fail safe solenoid valves. The pressure gauges are panel mounted to the side of the NEMA 4 enclosure.

Also Available:
Weights and Measures Certification, includes Calibration and Documentation

Weights and Measures Certification is required when you are transferring custody of fuel to another party. The Weights and Measures Field Inspector requires some additional hardware to allow them to do a field evaluation of the calibration of the dispenser: (1) have a switch that will allow the inspector to change the GGE volume display into a Mass volume display; (2) connect the Rosemount 275 Hand Held Programmer and access the Audit Trail inside the Micro Motion Transmitter; (3) manufacturer to recalibrate the dispenser and seal all enclosures; and (4) maintain a database on meter calibration and location of dispenser.
 

Contact Wise Gas for Pricing

 

 

TGT-K62-2-DH38
Twin Stand Alone CNG Vehicle Dispenser

This dispenser is a two-line dispenser that independently meters the gas and gives you a display on both sides of the dispenser. The dispenser has four 4-20ma output that can send flow or temperature to a controller. The dispenser has a dry contact and a 120v hook switch for an "in use" signal and will send pulses to a card reader or a console. The Micro Motion Transmitters are located within the dispenser body and are factory set and calibrated before shipment. TGT assembles an AGA 1-93 approved Parker Paraflex CNG fill hose on all its dispensers. The breakaway is the Snap-tite Inline type with a unique vent breakaway attached to the fill hose breakaway. All 1999 and later CNG Dispensers have an ASME pressure relief valve inside the dispenser cabinet with a vent stack up through the retractor pole. The cabinet is constructed of 11 gauge cold roll steel with a powder coat finish then a high quality mirror stainless steel trim is attached to the outside of the cabinet which will give you years of new appearing equipment. As an option, this dispenser can temperature compensate the fill pressure of the gas and do electronic sequencing of the gas from the storage to the dispenser.

 

Each Includes:
2    Retractors
2    Solenoid Valves
2    Pressure Gauges
2    Manual Shutoff Valve
2    Snap-tite Inline Hose Breakaways/ TGT Vent Hose Breakaways
2    12' x 3/8" Hose Assemblies (electrically conductive CNG twin hose)
2    Micro Motion DH38 Mass Flow Meter (rated at 5000psi, 50 lbs./minute, 1000 cfm)
1    Price Change Communicator
1    Concrete Island Form
2    ASME Relief Valves set at 125% of Vehicle Operating Pressure
  Powder Coated Steel Chassis w/ Stainless Steel Trim
Optional:
NGV1 Type 2 Refueling Connector (Staubli)
NGV1 Type 1 Refueling Nozzle Sherex CT1000
2 - Parker Finite J2SD Filters Installed in Dispenser
Dispenser Base Shear Breakaway System Installed in Dispenser
Temperature Compensation from the dispenser
Two Drop Solenoid Valve Panel
Custom screen printed face plates

Also Available:
Weights and Measures Certification, includes Calibration and Documentation
Weights and Measures Certification is required when you are transferring custody of fuel to another party. The Weights and Measures Field Inspector requires some additional hardware to allow them to do a field evaluation of the calibration of the dispenser: (1) have a switch that will allow the inspector to change the GGE volume display into a Mass volume display; (2) connect the Rosemount 275 Hand Held Programmer and access the Audit Trail inside the Micro Motion Transmitter; (3) manufacturer to recalibrate the dispenser and seal all enclosures; and (4) maintain a database on meter calibration and location of dispenser.

Contact Wise Gas for Pricing

 

TGT-T7104-12CNG50
One Hose Stand Alone Transit CNG Dispenser

This dispenser is a single-line dispenser that meters the gas and gives you a display on both sides of the dispenser. The dispenser has 1, 4-20mA output that can send flow or temperature to a remote controller. The dispenser has a 120VAC hook switch for an "in use" signal and will send pulses to a card reader or a console. The Micro Motion ® sensors and Transmitters are located within the dispenser body and are factory set up and calibrated before shipment. TGT assembles an AGA 1-93 approved Parker Parflex CNG fill hose on all its dispensers. The Breakaway is the Sherex In-Line type with a unique vent Breakaway attached to the fill hose breakaway. All TGT CNG Dispensers have an ASME pressure relief valve inside the dispenser cabinet with a vent stack up through the dispenser body. The cabinet is constructed of 11-gauge cold roll steel with a powder-coated finish; stainless steel material is optional. The high body style gives you the look of contemporary gasoline dispenser. The standard color is black but any custom colors can be applied to the dispenser body. This dispenser is rated for a MAWP of 4500psi. This dispenser will temperature compensate the fill using the Acufill fill algorithm. It will also supply the compressor with a dry contact or a 120VAC output as an in-use signal.

 

Each Includes:
1    Manual shut off valve 3/4" port Sequencing Valves
1    Inline Sherex hose break away
1    Sherex CT5000 Nozzle
1    Automatic air operated ball valve with 3/4" port
1    3/4" x 3/8" fill hose
1    ASME Relief Valve installed in dispenser body and vented out top
1    Parker Finite J6 Filter. grade 4 element
1    Micro Motion CNG 50 Meter rated for 185lbs per minute
1    6000 psi pressure gage
1    Pit box to support dispenser in concrete
1    TGT Display electronics with backlighted displays

Tubing inside dispenser 3/4" .095 seamless stainless steel ASTM A269 or A213 Equivalent
4500 PSI working pressure

Optional:
Two Drop Sequencing Solenoid Valve Panel Remote from Dispenser
Two Drop Sequencing ˝" Ball Valve Panel Remote from Dispenser
NGV1 Type 2 Refueling Connector Nozzle (Staubli)
NGV1 Type 1 Refueling Nozzle Sherex CT1000
2 Parker Finite J2SD Filters Installed in Dispenser w/ Block and Bleed Valves
Dispenser Base Shear Break-away System Installed in Dispenser
Stainless Steel Body with powder coat paint
Pressure Regulator used when dual pressure and elevated storage
Upgrade to ˝" Hose
High Flow Rate Nozzles call for quote

This dispenser is manufactured under the guidelines of:
NFPA 52
NFPA 70 (NEC)
ANSI/IAS NGV 4.0-1999 CSA 12.00-M99
ANSI B31.3
CE (on request)

Contact Wise Gas for Pricing

 


TGT-FP410ST
Single Hose CNG Fill Post

Single Hose Fill Post with integral vent hose breakaway. The fill post body has a 5000 psi gauge and a manual shut off valve installed in the face of the body. The fill post has the NFPA required signs printed on the face of the body. All tubing is 1/4" .035 316 seamless, stainless steel and the hoses are Parker Paraflex AGA 1-93 approved assemblies. All tube fittings are Swagelok brand. The fill post body is mounted on a 2" aluminum post that can be inserted into a sleeve poured into a concrete bumper or mounted on a guard rail. The sleeve can be supplied as an extra or a drawing is supplied at no extra charge.

 

Each Include:
1    Manual Shut Off Valve
1    5000 psi. Gauge
1    2" Aluminum Pole
1    Hose Retractor
1    12' x 1/4" Parker Paraflex CNG Hose Assembly
1    Three-way 1/4" Ball valve
1    Snap-tite Inline Breakaway
Available for this Post:
1/2", 3/8", or 3/4" tubing
1/2", 3/8", or 3/4" hose
NGV-1 Type 2 Refueling Nozzle
Custom Screen Printed Face Plates

Contact Wise Gas for Pricing

 


TGT-FP420ST
Twin Hose CNG Fill Post

Twin Hose Fill Post with integral vent hose breakaway. The fill post body has a 5000 psi gauge and a manual shut off valve installed in the face of the body. The fill post has the NFPA required signs printed on the face of the body. All tubing is 1/4" .035 316 seamless, stainless steel and the hoses are Parker Paraflex AGA 1-93 approved assemblies. All tube fittings are Swagelok brand. The fill post body is mounted on a 2" aluminum post that can be inserted into a sleeve poured into a concrete bumper or mounted on a guard rail. The sleeve can be supplied as an extra or a drawing is supplied at no extra charge.

 

Each Includes:
1    Manual Shut Off Valve
1    5000 psi. Gauge
1    2" Aluminum Pole
2    Hose Retractors
2    12' x 1/4" Parker Paraflex CNG Hose Assembly
2    Three-way 1/4" Ball valve
2    Snap-tite Inline Breakaway
Available for this Post:
1/2", 3/8", or 3/4" tubing
1/2", 3/8", or 3/4" hose
NGV-1 Type 2 Refueling Nozzle
Custom Screen Printed Face Plates

Contact Wise Gas for Pricing

 


TGT-FP430ST
Three Hose CNG Fill Post

Three Hose Fill Post with integral vent hose breakaway. The fill post body has a 5000 psi gauge and a manual shut off valve installed in the face of the body. The fill post has the NFPA required signs printed on the face of the body. All tubing is 1/4" .035 316 seamless, stainless steel and the hoses are Parker Paraflex AGA 1-93 approved assemblies. All tube fittings are Swagelok brand. The fill post body is mounted on a 2" aluminum post that can be inserted into a sleeve poured into a concrete bumper or mounted on a guard rail. The sleeve can be supplied as an extra or a drawing is supplied at no extra charge.
 
Each Includes:
1    Manual Shut Off Valve
1    5000 psi. Gauge
1    2" Aluminum Pole
3    Hose Retractors
3    12' x 1/4" Parker Paraflex CNG Hose Assembly
3    Three-way 1/4" Ball valve
2    Snap-tite Inline Breakaway
Available for this Post:
1/2", 3/8", or 3/4" tubing
1/2", 3/8", or 3/4" hose
NGV-1 Type 2 Refueling Nozzle
Custom Screen Printed Face Plates

Contact Wise Gas for Pricing
 

 


TGT-FP440ST
Four Hose CNG Fill Post

Four Hose Fill Post with integral vent hose breakaway. The fill post body has a 5000 psi gauge and a manual shut off valve installed in the face of the body. The fill post has the NFPA required signs printed on the face of the body. All tubing is 1/4" .035 316 seamless, stainless steel and the hoses are Parker Paraflex AGA 1-93 approved assemblies. All tube fittings are Swagelok brand. The fill post body is mounted on a 2" aluminum post that can be inserted into a sleeve poured into a concrete bumper or mounted on a guard rail. The sleeve can be supplied as an extra or a drawing is supplied at no extra charge.
 
Each Includes:
1    Manual Shut Off Valve
1    5000 psi. Gauge
1    2" Aluminum Pole
4    Hose Retractors
4    12' x 1/4" Parker Paraflex CNG Hose Assembly
4    Three-way 1/4" Ball valve
2    Snap-tite Inline Breakaway
Available for this Post:
1/2", 3/8", or 3/4" tubing
1/2", 3/8", or 3/4" hose
NGV-1 Type 2 Refueling Nozzle
Custom Screen Printed Face Plates

 

 


Contact Wise Gas for Pricing